Re: CIPE, windows 2000 configuration

[Docume <docume,AT,lycos,DOT,es>]

> I don't think that Windows is convinced of your CLASS_C netmask with a 
>CLASS_A 
> network address (10.0.0.x).

the mask is correct, isn't it? 
It is a class A, 10.0.0.0/8

> 
> Also, I presume that the CIPE-Win32 service is running as is 
> /usr/sbin/ciped-cb -o /etc/cipe/options.

I don't know

> 
> Are both peers setup to listen to port 3333 ?

The windows 2000 don't has a fixed port configured.

> 
> DKW
> 
> On Wednesday 28 August 2002 03:34 pm, you wrote:
> > Ah! ok I didn't know anything about that bug.
> >
> > Well, here is some useful information:
> > cipcb0    Link encap:IPIP Tunnel  HWaddr
> >           inet addr:10.10.10.1  P-t-P:10.10.10.101  Mask:255.255.255.255
> >           UP POINTOPOINT RUNNING NOARP  MTU:1442  Metric:1
> >           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:100
> >           RX bytes:0 (0.0 b)  TX bytes:1728 (1.6 Kb)
> >
> > # cat /etc/cipe/options.cipcb0
> > # IPs reales
> > me 172.16.0.10:3333
> > peer 172.16.0.1
> >
> > # Circuito VPN
> > ipaddr  10.10.10.1
> > ptpaddr 10.10.10.101
> >
> > # Llave
> > key = f0274bb895d44b1eb9a89nnf0f0df
> >
> > # cat /etc/sysconfig/network-scripts/ifcfg-cipcb0
> > DEVICE=cipcb0
> > ONBOOT=yes
> > USERCTL=no
> >
> > Ok now the steps I do in the windows 2000 pro box:
> > 1- edit tcp/ip options into the cipe device, and configured an ip address
> > and mask (10.10.10.101/255.255.255.0). No gateway neither dns servers.
> > 2- from control panel I edit the cipe settings and created a new peer,
> > with the vpn info.
> > 3- I try to ping over the VPN circuit without response
> >
> > here is the route table of my w2k pro:
> >
> > 
>===========================================================================
> > Rutas activas:
> > Destino de red        Máscara de red   Puerta de acceso   Interfaz  
>Métrica
> >           0.0.0.0          0.0.0.0      172.16.0.10      172.16.0.1      1
> >          10.0.0.0        255.0.0.0     10.10.10.101    10.10.10.101      1
> >      10.10.10.101  255.255.255.255        127.0.0.1       127.0.0.1      1
> >    10.255.255.255  255.255.255.255     10.10.10.101    10.10.10.101      1
> >         127.0.0.0        255.0.0.0        127.0.0.1       127.0.0.1      1
> >        172.16.0.0    255.255.255.0       172.16.0.1      172.16.0.1      1
> >        172.16.0.1  255.255.255.255        127.0.0.1       127.0.0.1      1
> >    172.16.255.255  255.255.255.255       172.16.0.1      172.16.0.1      1
> >         224.0.0.0        224.0.0.0     10.10.10.101    10.10.10.101      1
> >         224.0.0.0        224.0.0.0       172.16.0.1      172.16.0.1      1
> >   255.255.255.255  255.255.255.255       172.16.0.1      172.16.0.1      1
> > Puerta de enlace predeterminada:       172.16.0.10
> > 
>===========================================================================
> > Rutas persistentes:
> >   ninguno
> >
> >
> > Is anything wrong?
> >
> > On Wed, 28 Aug 2002, Damion Wilson wrote:
> > > I can try.
> > >
> > > Make sure the CIPE service is running. Also, there's a bug in the 
>control
> > > panel dialog where it doesn't save field contents properly all the time,
> > > so check to make sure that the static key and other settings are correct
> > > by reentering the control panel applet after exiting.
> > >
> > > DKW
> > >
> > > On Wednesday 28 August 2002 02:17 pm, you wrote:
> > > > Hi Damion,
> > > >
> > > > Thanks for your answer. :-]
> > > > I did that, but CIPE doesn't run, I can't connect.
> > > > I configured and ip address and mask in the cipe network adapter.
> > > > Then I went to cipe settings and configured the VPN.
> > > >
> > > > Are those steps corrects?
> > > > Can you give me hand with cipe?
> > > >
> > > > See you.
> > > >
> > > > On Wed, 28 Aug 2002, Damion Wilson wrote:
> > > > > Yes. The Cipe network adapter must be configured via TCP/IP settings
> > > > > before it can have peers added to it via the Cipe control panel
> > > > > applet.
> > > > >
> > > > > DKW
> > > > >
> > > > > On Wednesday 28 August 2002 12:22 pm, Docume wrote:
> > > > > > Hi again,
> > > > > >
> > > > > > I resolve the problem with cipe and my linux server, I have it
> > > > > > running correctly. Now the problem is how to configure my windows
> > > > > > 2000
> > > > > >
> > > > > > I note that there is a new open into my control panel called CIPE
> > > > > > Settings, I configured the connection there, but I can't connect
> > > > > > yet to my linux and I don't know the reason.
> > > > > >
> > > > > > Should I need to configure the cipe interface, the tcp/ip 
>settings?
> 
> 
> 
>