<< | Thread Index | >> ]    [ << | Date Index | >> ]

Subject: Re: Cipe Win32 is not working always 0 bytes
From: Damion Wilson <dwilson,AT,ibl,DOT,bm>
Date: Thu, 28 Nov 2002 02:57:52 +0100
In-reply-to: <BIEDKIEGNDKDPPPKCJPFAEEECAAA.novais@oninetspeed.pt>

Hmm,

For me it does start automatically (on both of my setups). There may be some 
networking component that won't let it start when it tries to. What you can 
do is to make Windows try to start the service again if it fails the first 
time. This is in the Services control panel applet somewhere.

DKW

On Wednesday 27 November 2002 06:43 pm, you wrote:
> Dear Damion and Olaf,
>
> Thank you both for the help.
>
> I had 2 problems:
>  The 1st one  on the PtP netmask. I found that I had an error there,
> instead of 255.255.0.0 I had 255.255.255.o. So the start point and end poit
> weren't on the same subnet.
>
> The 2nd one was on the services, the "DKW Heavy Industries VPN Adapter.
> Service" is set to automatic start but It was stopped (and it never starts
> automatically) and I had to start it manually to put it working.
>
> For the 1st error there is no cure (except start opening my eyes or change
> my glasses) for the second , do you have any solution?
>
> Best regards,
>
> António Novais
>
> -----Original Message-----
> From: Damion Wilson [mailto:dwilson,AT,ibl,DOT,bm
> Sent: quarta-feira, 27 de Novembro de 2002 16:48
> To: Antonio Novais
> Cc: cipe-l,AT,inka,DOT,de
> Subject: Re: Cipe Win32 is not working always 0 bytes
>
> You don't need to add any routes to get a basic peer to peer setup going
> between CIPE's (any platform). As long as the peer information is setup
> correctly in CIPE and the netmasks put both addresses in the same subnet,
> you
> should be able to ping across the link. You don't show the IP addresses on
> the interfaces, so I can't comment much further.
>
> DKW
>
> On Wednesday 27 November 2002 04:53 am, you wrote:
> > Dear Damion,
> >
> > I'm having problems implementing Cipe, description in the below mails.
> >
> > Could you help me please?
> >
> > Best regards,
> >
> > Antonio Novais
> >
> >
> > -----Original Message-----
> > From: Antonio Novais [mailto:novais,AT,oninetspeed,DOT,pt
> > Sent: terca-feira, 26 de Novembro de 2002 21:33
> > To: Olaf Titz
> > Subject: RE: Cipe Win32
> > Importance: High
> >
> > I Know how to do it in Windows , you can say unfortunately...
> > And I understand the linux commands logic (they are similar)
> >
> > What should be the exact route  to add?
> >
> > Route add 192.168.30.0 mask 255.255.255.0 gateway 192.168. ???.???
> >
> > What should be the gateway? I think 192.168.30.1 but it doesn't work,
> > result:
> >
> > C:\>route add 192.168.30.0 mask 255.255.255.0 192.168.30.1
> > The route addition failed: Either the interface index is wrong or the
> > gateway do
> > es not lie on the same network as the interface. Check the IP Address
>
> Table
>
> > for
> > the machine.
> >
> > Because It cannot find the 192.168.30.1.  Is a problem of the gateway IP
> > , or I have to add lots of routes manually?
> >
> > If yes could you send it in linux commands in order that I "translate"
>
> them
>
> > to windows.
> >
> > Many thanks
> >
> > Antonio Novais
> >
> > -----Original Message-----
> > From: Olaf Titz [mailto:olaf,AT,bigred,DOT,inka,DOT,de
> > Sent: terca-feira, 26 de Novembro de 2002 20:49
> > To: Antsnio Novais
> > Subject: Re: Cipe Win32
> >
> > > When I enable the connection it seems to be OK but nothing works, It
> >
> > changes
> >
> > > de routing table adding the 192.168.30.10 there:
> >
> > Not quite. Look exactly at the numbers.
> >
> > > Network Destination
> > > Netmask
> > > Gateway
> > > Interface
> > > Metric
> > > 192.168.31.0
> > > 255.255.255.0
> > > 192.168.31.10
> > > 192.168.31.10
> > > 1
> > > 192.168.31.10
> > > 255.255.255.255
> > > 127.0.0.1
> > > 127.0.0.1
> > > 1
> > > 192.168.31.255
> > > 255.255.255.255
> > > 192.168.31.10
> > > 192.168.31.10
> > > 1
> > >
> > >
> > >
> > > I try to ping 192.168.30.1 and it always go through the DSL normal
> > > connection and always 0 bytes in the traffic of the Cipe adapter.
> >
> > You don't add a route to the peer or its network (192.168.30.*) at
> > all. The route which is added automatically goes to your own CIPE
> > interface, not the other side's. Looks like you have to add the route
> > manually. Unfortunately I don't know how exactly, because of my
> > missing Windows knowledge. :-)
> >
> > regards
> >
> > Olaf
> >
> >
> > -----Original Message-----
> > From: Antonio Novais [mailto:novais,AT,oninetspeed,DOT,pt
> > Sent: terca-feira, 26 de Novembro de 2002 18:14
> > To: Olaf.Titz,AT,inka,DOT,de
> > Subject: Cipe Win32
> >
> > Dear Olaf,
> >
> > I've installed CIPE-Win32-2.0-pre15 in Windows 2000 pro, Service Pack 2.
> >
> > I also have an DSL connection (NOT fixed IP). But normally I configure
> > the current IP in Cipe (and I used 0.0.0.0 in other experiences)
> >
> > My TCP/IP parameters in CIPE VPN adapter are  IP 192.168.31.10  mask
> > 255.255.255.0
> >
> > PtP configurations , the Peer IP is 192.168.30.1, and I have a static
> > Key.
> >
> > I'm triyng to establish a connection with a linux server (Debian).
> >
> > When I enable the connection it seems to be OK but nothing works, It
> > changes de routing table adding the 192.168.30.10 there:
> >
> > Network Destination   Netmask Gateway Interface       Metric
> > 192.168.31.0  255.255.255.0   192.168.31.10   192.168.31.10   1
> > 192.168.31.10 255.255.255.255 127.0.0.1       127.0.0.1       1
> > 192.168.31.255        255.255.255.255 192.168.31.10   192.168.31.10   1
> >
> >
> > I try to ping 192.168.30.1 and it always go through the DSL normal
> > connection and always 0 bytes in the traffic of the Cipe adapter.
> >
> >
> > What can be wrong? How can I test if Cipe is working?
> >
> > Best Regards,
> >
> > Antonio Novais





<< | Thread Index | >> ]    [ << | Date Index | >> ]