<< | Thread Index | >> ]    [ << | Date Index | >> ]

Subject: Re: Bridging Support in win32 version
From: Phil Scarratt <fil,AT,draxsen,DOT,com>
Date: Sat, 15 Mar 2003 13:20:09 +0100
In-reply-to: <FNEHLKGMPALOKJFOJJBJIELJCMAA.tparker@netspace.net.au>

IPCOnfig Output:

Ethernet adapter CIPE:

         Connection-specific DNS Suffix  . :
         IP Address. . . . . . . . . . . . : 192.168.1.1
         Subnet Mask . . . . . . . . . . . : 255.255.255.0
         Default Gateway . . . . . . . . . :

Ethernet adapter Local Area Connection:

         Connection-specific DNS Suffix  . :
         IP Address. . . . . . . . . . . . : 192.168.1.201
         Subnet Mask . . . . . . . . . . . : 255.255.255.0
         Default Gateway . . . . . . . . . : 192.168.1.254

Control Panel:

Local IP Address: 222.222.222.222 PORT: 10001
(The IP addres put here is the IP address of the internet connection on 
the gateway machine on the Win2k client's local net)
Peer IP Address: 111.111.111.111 PORT: 10000
(This IP address is the internet connection's IP address on the remote 
peer - Linux machine)
Local PTP Address: 192.168.1.1
Peer PTP Address: 192.168.0.1
Status: Enabled? is ticked
Key Settings:
Static Key: 66332547659682279845607406745812
Cipher: Blowfish
Timeout (seconds): 600

Note: I have tried the remote node (linux machine) with a connection 
from my gateway machine on the local network (also a linux machine) and 
all works fine so I know the remote setup is OK. I'm pretty sure I setup 
the firewall/NAT correctly to try from the Win2k machine. However, 
packets aren't even getting to the local gateway. Pinging 192.168.0.1 
from the win2k machine goes no where - a tcpdump on the gateway shows 
nothing arriving on the eth0 interface (local network) on the gateway. 
In fact Win2k reports 0 bytes sent and received on the CIPE adapter no 
matter how much I ping.

I have also tried with no cipher or static key settings, and a pure 
digit key as above, to no avail. Hoping someone has a clue. I've had to 
revert to PPTP for the time being.

Thanks again for the help.

puzzled-fil

Tom Parker wrote:
> Hi folks,
> 
> Managed to get both rh8.0 and openap linux to cipe to a win2k sp3 box just
> fine (Phil send you ipconfig output and your cipe control panel
> configuration - are you sure you've got the local ip address right and have
> chosen a suitably unused UDP port?).
> 
> I was hoping to do some bridging using openap on an access point - to bridge
> over cipe using protocol version 4 to the windows box.  I think I'm being a
> bit ambitious here - the version 4 packets are ignored by the win32 end.  Is
> there any protocol version 4 support in the win32 version?
> 
> Thanks,
> Tom
> 
> ----------------------------------
> Tom Parker tparker,AT,netspace,DOT,net,DOT,au
> http://www.wiresncode.com/projects
> 
> 
> 
> 
> 
> --
> Message sent by the cipe-l,AT,inka,DOT,de mailing list.
> Unsubscribe: mail majordomo,AT,inka,DOT,de, "unsubscribe cipe-l" in body
> Other commands available with "help" in body to the same address.
> CIPE info and list archive: 
><URL:http://sites.inka.de/~bigred/devel/cipe.html>

-- 
Phil Scarratt
Draxsen Technologies
IT Contractor/Consultant
0403 53 12 71





<< | Thread Index | >> ]    [ << | Date Index | >> ]