<< | Thread Index | >> ]    [ << | Date Index | >> ]

Subject: RE: Bridging Support in win32 version
From: "Tom Parker" <tparker,AT,netspace,DOT,net,DOT,au>
Date: Sun, 16 Mar 2003 00:49:09 +0100
In-reply-to: <3E731732.2080300@draxsen.com>

Phil,

I think your problem is that you need to use the ip address of the "Ethernet
adapter Local Area Connection" as the local ip address.

I think your local ip address should be 192.168.1.201 - the daemon won't
start because it can't find an interface with 192.168.1.1 as it's address.

Perhaps I am missing something here, but I think that is what is wrong.  You
should also make sure you can ping the peers interface ie. try ping
192.168.0.1

Cheers,
Tom

> IPCOnfig Output:
>
> Ethernet adapter CIPE:
>
>          Connection-specific DNS Suffix  . :
>          IP Address. . . . . . . . . . . . : 192.168.1.1
>          Subnet Mask . . . . . . . . . . . : 255.255.255.0
>          Default Gateway . . . . . . . . . :
>
> Ethernet adapter Local Area Connection:
>
>          Connection-specific DNS Suffix  . :
>          IP Address. . . . . . . . . . . . : 192.168.1.201
>          Subnet Mask . . . . . . . . . . . : 255.255.255.0
>          Default Gateway . . . . . . . . . : 192.168.1.254
>
>
> Control Panel:
>
> Local IP Address: 222.222.222.222 PORT: 10001
> (The IP addres put here is the IP address of the internet connection on
> the gateway machine on the Win2k client's local net)
> Peer IP Address: 111.111.111.111 PORT: 10000
> (This IP address is the internet connection's IP address on the remote
> peer - Linux machine)
> Local PTP Address: 192.168.1.1
> Peer PTP Address: 192.168.0.1
> Status: Enabled? is ticked
> Key Settings:
> Static Key: 66332547659682279845607406745812
> Cipher: Blowfish
> Timeout (seconds): 600
>
>
> Note: I have tried the remote node (linux machine) with a connection
> from my gateway machine on the local network (also a linux machine) and
> all works fine so I know the remote setup is OK. I'm pretty sure I setup
> the firewall/NAT correctly to try from the Win2k machine. However,
> packets aren't even getting to the local gateway. Pinging 192.168.0.1
> from the win2k machine goes no where - a tcpdump on the gateway shows
> nothing arriving on the eth0 interface (local network) on the gateway.
> In fact Win2k reports 0 bytes sent and received on the CIPE adapter no
> matter how much I ping.
>
> I have also tried with no cipher or static key settings, and a pure
> digit key as above, to no avail. Hoping someone has a clue. I've had to
> revert to PPTP for the time being.
>
> Thanks again for the help.
>
> puzzled-fil
>
> Tom Parker wrote:
> > Hi folks,
> >
> > Managed to get both rh8.0 and openap linux to cipe to a win2k
> sp3 box just
> > fine (Phil send you ipconfig output and your cipe control panel
> > configuration - are you sure you've got the local ip address
> right and have
> > chosen a suitably unused UDP port?).
> >
> > I was hoping to do some bridging using openap on an access
> point - to bridge
> > over cipe using protocol version 4 to the windows box.  I think
> I'm being a
> > bit ambitious here - the version 4 packets are ignored by the
> win32 end.  Is
> > there any protocol version 4 support in the win32 version?
> >
> > Thanks,
> > Tom
> >
> > ----------------------------------
> > Tom Parker tparker,AT,netspace,DOT,net,DOT,au
> > http://www.wiresncode.com/projects
> >
> >
> >
> >
> >
> > --
> > Message sent by the cipe-l,AT,inka,DOT,de mailing list.
> > Unsubscribe: mail majordomo,AT,inka,DOT,de, "unsubscribe cipe-l" in body
> > Other commands available with "help" in body to the same address.
> > CIPE info and list archive:
> <URL:http://sites.inka.de/~bigred/devel/cipe.html>
>
>
> --
> Phil Scarratt
> Draxsen Technologies
> IT Contractor/Consultant
> 0403 53 12 71
>
>
> --
> Message sent by the cipe-l,AT,inka,DOT,de mailing list.
> Unsubscribe: mail majordomo,AT,inka,DOT,de, "unsubscribe cipe-l" in body
> Other commands available with "help" in body to the same address.
> CIPE info and list archive:
> <URL:http://sites.inka.de/~bigred/devel/cipe.html>
>





<< | Thread Index | >> ]    [ << | Date Index | >> ]